WorkBench 1007 Project Development Kit


1007 Base

Use to prototype, manage electronics, and transport your projects.

14” x 8” x 1”
Approximate 54 sq. in. work surface
10x7 primary matrix; 9x6 secondary matrix
1/8” acrylic
Choice of colors:

  • Black Gloss - great for most projects

  • Black Matte - easy to photograph; fingerprint resistant

  • Neon Green - edgy and eye-popping

Holes on legs align with Cover; screw together for security
Hang by handle for easy temporary storage
Holes on legs enable more permanent mount, if desired


1007 Cover

Protects and makes projects easily and safely portable.

10” x 7.5” x 3.5”
Clear acrylic, gloss


Approx. 2.5” clearance between Base and Cover when attached
Ample space for wire or cord through-access
Ventilation to prevent electronics over-heating
Easily and securely snaps on and off the Base
Holes on sides align with Base; screw Cover to Base for extra security

> Using the Cover Demo Video


Four 2x3 Clicks

Mount electronics using a Slide, or direct attach methods.
Clicks into the Base for easy management and layout of project.

Mounting platform: 2.53” x 3.35” (64.3mm x 85.4mm)
ABS plastic; 3D print

Use with provided Slides for Arduino or Raspberry Pi boards

Direct Mount Other Electronics

> Electronics Mounting Guide


One 1x3 Click

Mount electronics using a Slide, or direct attach methods.
Clicks into the Base for easy management and layout of project.

Mounting platform: 1.56” x 3.35” (40mm x 85.4mm)
ABS plastic; 3D print


Use with provided Slide for AdaFruit Feather, FeatherWing or Particle Argon, Boron or Xenon boards

Direct Mount Other Electronics

> Electronics Mounting Guide


One Slide, Arduino UNO

Mount Arduino UNO, or use with any board with the same configuration, including the Arduino MEGA

ABS plastic; 3D print
Assemble with a 2x3 Click

Assembly includes M2.5 hex nuts installed in the raised bosses; hex nuts enable you to firmly attach and easily remove PCBs multiple times without causing any damage to the Slide.
The Arduino MEGA attaches to this Slide with four screws only, and has a partial overhang.

> Click/Slide Assembly Guide


One Slide, Raspberry Pi 2/3

Mount Raspberry Pi 2 or 3 or any board with the same configuration.

ABS plastic; 3D print
Assemble with a 2x3 Click

Assembly includes M2.5 hex nuts installed in the raised bosses; hex nuts enable you to firmly attach and easily remove electronics multiple times without causing any damage to the Slide.

> Click/Slide Assembly Guide


One Slide, Feather/Particle

Mount AdaFruit Feather 32u4 Basic, or Particle Argon, Boron or Xenon, or any board with the same configuration. Also accepts the Adafruit FeatherWing Kit (terminal block breakout board)

ABS plastic; 3D print
Assemble with a 1x3 Click

Assembly includes M2.5 hex nuts installed in the raised bosses; hex nuts enable you to firmly attach and easily remove PCBs multiple times without causing any damage to the Slide.

> Click/Slide Assembly Guide


IMG_1068.jpg

One Hardware Packet, 1007

Includes all the small hardware needed to get started with the WorkBench 1007

13 M2.5 hex nuts; for Click/Slide assembly
13 M3.0 hex nuts; for Click/Slide assembly
1 M2.5 x 20 screw; for Click Slide assembly
13 M2.5 x 6 machine screws; attach electronics to Click/Slide assemblies
4 Nylon male/female standoffs; use to build electronics tower
8 Tubular standoffs; direct-attach electronics to Clicks
9 #2 x 5/8” self-tapping screws; direct-attach electronics to Clicks
2 8-32 x 7/16 machine screws; for cable management
2 8-32 nyloc nuts; for cable management
2 Cable tie saddle mounts; for cable management
2 Zipties, small; for cable management

> Electronics Mounting Guide

> Click/Slide Assembly Guide